VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791SERVICE MANUALGPC SERIES GAS PASTA COOKERSMODELSGPC12 ML-126881GPC12S
– 10 –CONTROL BOX HOUSINGWARNING: DISCONNECT (UNPLUG) ELECTRICALPOWER SUPPLY AND PLACE A TAG AT THEDISCONNECT SWITCH INDICATING YOU AREWORKING ON THE
– 11 –5. Remove the two holding hex head screwssecuring the mounting bracket to the highlimit.6. Follow the high limit capillary to the packingnut lo
– 12 –8. Remove the high limit bulb from the tankmounting brackets.9. Reverse procedures to install new high limit.NOTE: When installing a new high li
– 13 –6. With an offset screwdriver, remove the twoscrews from the ignitor/pilot holding bracketand pull the assembly from the cooker tank.7. Reverse
– 14 –GAS COMBINATION VALVEWARNING: DISCONNECT (UNPLUG) ELECTRICALPOWER SUPPLY AND PLACE A TAG AT THEDISCONNECT SWITCH INDICATING YOU AREWORKING ON T
– 15 –OVERFLOW HOSESWARNING: DISCONNECT (UNPLUG) ELECTRICALPOWER SUPPLY AND PLACE A TAG AT THEDISCONNECT SWITCH INDICATING YOU AREWORKING ON THE CIRC
– 16 –DOORS1. There are two doors on the pasta cooker.Open the door to be removed.2. Loosen the nuts and bolts securing themounting bracket to the fra
– 17 –Cam Switch1. Remove the two nuts and bolts holding thecam switch to the motor mounting bracket.2. Remove wiring from the cam switch.3. Remove th
– 18 –3. Remove the nuts and bolts securing theelectrical cord holding straps (two places).4. Pull the ignition cable from the spark ignitor,and remov
– 19 –POWER SUPPLY BOX INTERNALCOMPONENTSWARNING: DISCONNECT (UNPLUG) ELECTRICALPOWER SUPPLY AND PLACE A TAG AT THEDISCONNECT SWITCH INDICATING YOU A
– 2 –© VULCAN-HART COMPANY, 2002TABLE OF CONTENTSGENERAL ...
– 20 –COOKER TANKWARNING: DISCONNECT (UNPLUG) ELECTRICALPOWER SUPPLY AND PLACE A TAG AT THEDISCONNECT SWITCH INDICATING YOU AREWORKING ON THE CIRCUIT
– 21 –RINSE TANKWARNING: DISCONNECT (UNPLUG) ELECTRICALPOWER SUPPLY AND PLACE A TAG AT THEDISCONNECT SWITCH INDICATING YOU AREWORKING ON THE CIRCUIT.
– 22 –7. Remove the center strip between the cookerand rinse tank.8. Disconnect the center rubber drain hose.9. Disconnect the water fill hose fitting
– 23 –A. To adjust, remove the cap covering themanifold pressure adjustment screw. Turnthe recessed manifold pressureadjustment screw counterclockwis
– 24 –OPTIONAL BASKET LIFT ASSEMBLYWARNING: DISCONNECT (UNPLUG) ELECTRICALPOWER SUPPLY AND PLACE A TAG AT THEDISCONNECT SWITCH INDICATING YOU AREWORK
– 25 –VERIFICATION OF SPARK ATIGNITORWARNING: DISCONNECT (UNPLUG) ELECTRICALPOWER SUPPLY AND PLACE A TAG AT THEDISCONNECT SWITCH INDICATING YOU AREWO
– 26 –ELECTRICAL OPERATION WIRING DIAGRAMS
– 27 –TROUBLESHOOTINGSMOTPMYSSESUACELBISSOP.etingitonseodsaG.krapsoN.esnesemalf/retinginoedortceledetrohS.NEPO)egatlovhgih(elbacrotingI.noitcnuflamyal
– 28 –NOTESFORM 31207 (April 2002) PRINTED IN U.S.A.
– 3 –TABLE OF CONTENTS (Cont.)SERVICE PROCEDURES AND ADJUSTMENTS ...
– 4 –INTRODUCTIONProcedures in this manual will apply to all modelsunless specified. Pictures and illustrations can be ofany model unless the picture
– 5 –REMOVAL AND REPLACEMENT OF PARTSCOVERS AND PANELSWARNING: DISCONNECT (UNPLUG) ELECTRICALPOWER SUPPLY AND PLACE A TAG AT THEDISCONNECT SWITCH IND
– 6 –3. Disconnect the water hoses and remove thepanel from the rinse station.4. Reverse the procedure to install.Upper and Lower Lift Mechanism Panel
– 7 –CONTROL PANEL COMPONENTSWARNING: DISCONNECT (UNPLUG) ELECTRICALPOWER SUPPLY AND PLACE A TAG AT THEDISCONNECT SWITCH INDICATING YOU AREWORKING ON
– 8 –Relay1. Remove the cooker control panel as outlinedunder Covers and Panels.2. Remove all the wiring associated with therelay.3. Remove the two ho
– 9 –3. Disconnect the water hoses and remove thecontrol panel from the rinse station.NOTE: When hose fittings are removed, inspect thehose washers fo
Kommentare zu diesen Handbüchern