Vulcan VG30 Bedienungsanleitung Seite 1

A product of VULCAN-HART LOUISVILLE, KY 40201-0696F25121(February 2003)- NOTICE -This Manual is prepared for the use of trained Vulcan ServiceTechnici

GAS BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTSF25121 (February 2003) Page 10 of 327. To install:A. With drive key on shaft, install motor togea

GAS BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTSF25121 (February 2003)Page 11 of 32NOTE: On the bottom lift arm bushing, the bushinghead must be

GAS BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTSF25121 (February 2003) Page 12 of 3210. Check for proper operation.PILOT BURNERWARNING: DISCONNEC

GAS BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTSF25121 (February 2003)Page 13 of 32RIGHT SIDE REAR VIEW SHOWNNOTE: Runner tube slides onto the ga

GAS BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTSF25121 (February 2003) Page 14 of 32A. Slowly release downwards force to removespring tension. B.

GAS BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTSF25121 (February 2003)Page 15 of 32SERVICE PROCEDURES AND ADJUSTMENTSWARNING: CERTAIN PROCEDURE

GAS BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTSF25121 (February 2003) Page 16 of 3212. Repeat the average temperature calculation forup to thr

GAS BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTSF25121 (February 2003)Page 17 of 32SPARK IGNITION TESTIf the ignition control module is not gen

GAS BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTSF25121 (February 2003) Page 18 of 3211. Turn on/off switch on and set the temperaturedial to ca

GAS BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTSF25121 (February 2003)Page 19 of 3210. Manually operate pan position/down limit switchand obser

GAS BRAISING PANSF25121 (February 2003) Page 2 of 32TABLE OF CONTENTSGENERAL ...

GAS BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTSF25121 (February 2003) Page 20 of 322. Ignition control module is energized and trialfor igniti

GAS BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTSF25121 (February 2003)Page 21 of 32FRONT VIEW OF BURNER AIR SHUTTERSHOWNNOTE: Accurate gas pres

GAS BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTSF25121 (February 2003) Page 22 of 32SIDE VIEW SHOWNDC MOTOR CONTROLLER TEST1. Lower the pan to

GAS BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTSF25121 (February 2003)Page 23 of 32LEFT SIDE VIEW SHOWNLEFT SIDE VIEW SHOWN RIGHT SIDE REAR VIE

GAS BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTSF25121 (February 2003) Page 24 of 323. To adjust:A. Place a 1 5/8" wrench on the lid sprin

GAS BRAISING PANS - ELECTRICAL OPERATIONF25121 (February 2003)Page 25 of 32ELECTRICAL OPERATIONCOMPONENT FUNCTIONBRAISING PAN CONTROLSTemperature Con

GAS BRAISING PANS - ELECTRICAL OPERATIONF25121 (February 2003) Page 26 of 32COMPONENT LOCATION

GAS BRAISING PANS - ELECTRICAL OPERATIONF25121 (February 2003)Page 27 of 32IGNITION CONTROL MODULEThe ignition control module is energized when 24 vo

GAS BRAISING PANS - ELECTRICAL OPERATIONF25121 (February 2003) Page 28 of 32SEQUENCE OF OPERATIONRefer to schematic diagram AI1341 for the electrical

GAS BRAISING PANS - ELECTRICAL OPERATIONF25121 (February 2003)Page 29 of 325. Pan reaches full tilt position, the up limit switchN.C. contacts open a

GAS BRAISING PANSF25121 (February 2003)Page 3 of 32GENERALINSTALLATION, OPERATIONAND CLEANINGRefer to the Installation & Operation Manual forspec

GAS BRAISING PANS - ELECTRICAL OPERATIONF25121 (February 2003) Page 30 of 32SCHEMATIC DIAGRAM

GAS BRAISING PANS - TROUBLESHOOTINGF25121 (February 2003)Page 31 of 32TROUBLESHOOTINGGAS HEATING (MANUAL LIFT OR MOTORIZED LIFT OPTION)SYMPTOMS POSSI

GAS BRAISING PANS - CONDENSED SPARE PARTS LISTF25121 (February 2003) Printed in U.S.A.MOTORIZED LIFT OPTION ONLYSYMPTOM POSSIBLE CAUSESPan will not ra

GAS BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTSF25121 (February 2003) Page 4 of 32REMOVAL AND REPLACEMENT OF PARTSCOVERS AND PANELSWARNING: DISC

GAS BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTSF25121 (February 2003)Page 5 of 328. Pull temperature dial from potentiometer shaftand remove mou

GAS BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTSF25121 (February 2003) Page 6 of 32LEFT SIDE VIEW SHOWN4. Pull temperature dial from potentiomete

GAS BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTSF25121 (February 2003)Page 7 of 32TOP VIEW SHOWNSIDE VIEW SHOWNNOTE: When installing, replace the

GAS BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTSF25121 (February 2003) Page 8 of 32G. Verify roller arm position on switch.1) Measure the distanc

GAS BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTSF25121 (February 2003)Page 9 of 32VG30 REAR VIEW SHOWN6. Reverse procedure to install and check f